Thursday, December 15, 2011

Cutting Rafters beyond doubt and Efficiently

One of the most time attractive tasks in homebuilding can be
the cutting of a roof. In some cases it can take as long to
cut and frame the roof as it does to frame the rest of the
house. It can also require a lot of space to get the job
done. It is in ones best interests to plan ahead while the
course of building to be ready when it comes time to cut
the roof.

Whether the roof be a easy gable roof or a complicated roof
with multiple hips and valleys you want to be able to cut
more than one rafter at a time. Sawhorses become a critical
commodity while the roof cutting phase of construction.
Cutting a half dozen or more rafters is what you want to try
for. To accomplish this there are a few options available to
the roof cutter.

Carpentry Framing

If you only have one set of horses, nail an eight foot 2x4
flat to the top of them. This will allow you to mark and
cut six or more rafters depending on their width.

The second selection is to use two pair of sawhorses. Just like
the old option, nail a 2x4 flat over the top of two
horses. In this instance you are not petite to an eight
foot 2x4. You can use an 8, 10, 12, or even a 16' 2x4
depending on how much room you have to work in.

The third selection is to make your own sawhorses out of a
2x10. Put legs on it just like a general sawhorse. Again,
your only limitation is what you have available for length
of 2x10 and how much room you have to work.

Another time saver is to make a rafter pattern. To do this,
pick the straightest piece if lumber you can find from the
rafter material. Once you have thought about the length of your
rafter from the plumb cut to the birdsmouth, the depth of
the birdsmouth, and the length of the rafter tail, transfer
this data to the material. After you have marked all
of this on the 2x, thought about and accurately cut the rafter.
This is going to be your pattern for the rest of the rafters
so you want to be accurate with your cuts.

The next move is to nail stops to the top of the pattern.
Cut two pieces of plywood about 6" long by 2 1/2" wide. Nail
one to the top of the 2x about 2" from the plumb cut,
letting it hang over both edges of the 2x one half inch.
Nail the other piece just above the birdsmouth. You now have
a pattern to mark the rest of your rafters without having to
measure each and every one of them.

When you are ready to start cutting the rafters, lay as many
boards on the horse as you can and have sufficient room for the
saw to fit in in the middle of each one. When laying the boards on the
horses, have all the crowns pointing in the same direction
(When seeing down a board while flat most boards are bowed
one way or the other. The convex side would be the crown).
Take the pattern and lay it on top of each board with the
plywood stops resting on the crowned edge and mark them.

You are now ready to cut rafters. When development your cuts, cut
the pencil line. Cut the plumb cut first and then move to
the birdsmouth and tail. Depending on how many rafters you
are cutting you may have to slide them back and forth so you
are not reaching over to far to make your cuts with the saw.
When cutting the birdsmouth it is okay to over cut it to
totally remove the material.

Homebuilding and cutting rafters can be a risky job.
Always practice caution and protection when framing or using a
skilsaw.

Mike Merisko (C) 2006

http://www.sawkerfs.com

Cutting Rafters beyond doubt and Efficiently

One of the most time attractive tasks in homebuilding can be
the cutting of a roof. In some cases it can take as long to
cut and frame the roof as it does to frame the rest of the
house. It can also require a lot of space to get the job
done. It is in ones best interests to plan ahead while the
course of building to be ready when it comes time to cut
the roof.

Whether the roof be a easy gable roof or a complicated roof
with multiple hips and valleys you want to be able to cut
more than one rafter at a time. Sawhorses become a critical
commodity while the roof cutting phase of construction.
Cutting a half dozen or more rafters is what you want to try
for. To accomplish this there are a few options available to
the roof cutter.

Carpentry Framing

If you only have one set of horses, nail an eight foot 2x4
flat to the top of them. This will allow you to mark and
cut six or more rafters depending on their width.

The second selection is to use two pair of sawhorses. Just like
the old option, nail a 2x4 flat over the top of two
horses. In this instance you are not petite to an eight
foot 2x4. You can use an 8, 10, 12, or even a 16' 2x4
depending on how much room you have to work in.

The third selection is to make your own sawhorses out of a
2x10. Put legs on it just like a general sawhorse. Again,
your only limitation is what you have available for length
of 2x10 and how much room you have to work.

Another time saver is to make a rafter pattern. To do this,
pick the straightest piece if lumber you can find from the
rafter material. Once you have thought about the length of your
rafter from the plumb cut to the birdsmouth, the depth of
the birdsmouth, and the length of the rafter tail, transfer
this data to the material. After you have marked all
of this on the 2x, thought about and accurately cut the rafter.
This is going to be your pattern for the rest of the rafters
so you want to be accurate with your cuts.

The next move is to nail stops to the top of the pattern.
Cut two pieces of plywood about 6" long by 2 1/2" wide. Nail
one to the top of the 2x about 2" from the plumb cut,
letting it hang over both edges of the 2x one half inch.
Nail the other piece just above the birdsmouth. You now have
a pattern to mark the rest of your rafters without having to
measure each and every one of them.

When you are ready to start cutting the rafters, lay as many
boards on the horse as you can and have sufficient room for the
saw to fit in in the middle of each one. When laying the boards on the
horses, have all the crowns pointing in the same direction
(When seeing down a board while flat most boards are bowed
one way or the other. The convex side would be the crown).
Take the pattern and lay it on top of each board with the
plywood stops resting on the crowned edge and mark them.

You are now ready to cut rafters. When development your cuts, cut
the pencil line. Cut the plumb cut first and then move to
the birdsmouth and tail. Depending on how many rafters you
are cutting you may have to slide them back and forth so you
are not reaching over to far to make your cuts with the saw.
When cutting the birdsmouth it is okay to over cut it to
totally remove the material.

Homebuilding and cutting rafters can be a risky job.
Always practice caution and protection when framing or using a
skilsaw.

Mike Merisko (C) 2006

http://www.sawkerfs.com

Cutting Rafters beyond doubt and Efficiently

No comments:

Post a Comment