Installing a prefabricated shower stall often turns out to be a tricky and time-consuming job that takes great practical skill, yet with sensible pre-planning and the right tools for the job, a expert consequent can be obtained by the mean home-handyman. Allow 3-4 days to complete the work and brush up on your carpentry, plumbing, wall-preparation and finishing skills because you're going to need them all!
To begin with, make sure you have the right equipment and tools before you begin the job. Importantly, buy the shower stall before building the frame it will fit in in order to get correct dimensions.
Carpentry Framing
You will need: a prefabricated shower, galvanic drill, plumb level, tape measure, caulk, screws, hole saw, shower/tub adhesive, tape, pencil, leather work gloves, hammer, work boots and an adjustable wrench. Protective eye-wear is also highly advisable (wear when using power tools.)
Getting the prefab shower into position can be the tricky part. You will need to fit it straight through an existing doorway or an covering window. In some instances, part of an covering wall may have to be removed in order to get the unit inside; seek expert advice first if required.
Because prefabricated shower stalls have watertight walls, cement-based backer boards are not needed.
It is advisable to install insulation in the middle of the studs in order to cut plumbing noise.
When drilling holes in the unit's walls to fit the faucet and shower arm, quantum carefully in progress and all the time wear protective eye-wear when drilling.
Position parts carefully and attach the unit to the framing. The drain piece, shower handle, escutcheon, and shower-head all need to be fitted correctly to preclude leakages and hereafter problems. All seams need to be caulked efficiently and a acceptable checking of any leaks needs specific attention; later corrections to any plumbing faults can be difficult to carry out.
Finally, discontinue the walls and fit a shower door or curtain bar. It is vital that you seal the joints in the middle of the bathroom walls and floor and shower enclosure with a good capability silicone! Installing water-resistant drywall colse to the top edge of the shower stall can be a wise, long-term investment; tiling the top edge is also a great idea as it will likely last a lot longer than wallpaper or paintwork.
If you aren't adept in skills like demolition, plumbing and drywalling, you may be best served by employing a noteworthy expert to carry out these tasks.
As a final reminder, installing prefabricated shower stalls can be quite fiddly and time-consuming. The plumbing especially has to be completed with some expertise in order to have a sound unit. Yet having said all this, a victorious shower premise is achievable if you take your time, check well for any leaks and consult an specialist for advice if the need arises.
Good luck!
Prefabricated Shower Stalls - Tips For InstallingInstalling a prefabricated shower stall often turns out to be a tricky and time-consuming job that takes great practical skill, yet with sensible pre-planning and the right tools for the job, a expert consequent can be obtained by the mean home-handyman. Allow 3-4 days to complete the work and brush up on your carpentry, plumbing, wall-preparation and finishing skills because you're going to need them all!
To begin with, make sure you have the right equipment and tools before you begin the job. Importantly, buy the shower stall before building the frame it will fit in in order to get correct dimensions.
Carpentry Framing
You will need: a prefabricated shower, galvanic drill, plumb level, tape measure, caulk, screws, hole saw, shower/tub adhesive, tape, pencil, leather work gloves, hammer, work boots and an adjustable wrench. Protective eye-wear is also highly advisable (wear when using power tools.)
Getting the prefab shower into position can be the tricky part. You will need to fit it straight through an existing doorway or an covering window. In some instances, part of an covering wall may have to be removed in order to get the unit inside; seek expert advice first if required.
Because prefabricated shower stalls have watertight walls, cement-based backer boards are not needed.
It is advisable to install insulation in the middle of the studs in order to cut plumbing noise.
When drilling holes in the unit's walls to fit the faucet and shower arm, quantum carefully in progress and all the time wear protective eye-wear when drilling.
Position parts carefully and attach the unit to the framing. The drain piece, shower handle, escutcheon, and shower-head all need to be fitted correctly to preclude leakages and hereafter problems. All seams need to be caulked efficiently and a acceptable checking of any leaks needs specific attention; later corrections to any plumbing faults can be difficult to carry out.
Finally, discontinue the walls and fit a shower door or curtain bar. It is vital that you seal the joints in the middle of the bathroom walls and floor and shower enclosure with a good capability silicone! Installing water-resistant drywall colse to the top edge of the shower stall can be a wise, long-term investment; tiling the top edge is also a great idea as it will likely last a lot longer than wallpaper or paintwork.
If you aren't adept in skills like demolition, plumbing and drywalling, you may be best served by employing a noteworthy expert to carry out these tasks.
As a final reminder, installing prefabricated shower stalls can be quite fiddly and time-consuming. The plumbing especially has to be completed with some expertise in order to have a sound unit. Yet having said all this, a victorious shower premise is achievable if you take your time, check well for any leaks and consult an specialist for advice if the need arises.
Good luck!
Prefabricated Shower Stalls - Tips For Installing
No comments:
Post a Comment