A lot of people's first idea in undertaking a remodeling project is to start with tearing down walls. That's an ambitious (if not impulsive) beginning to a project, with focused performance for one's built-up energy, but it's a decision that needs to be well thought about and fully realized before any actual work can safely begin. Walls are built for any reasons, whether as bearing walls designed to hold up a house and transfer loads from above, or as partitions designed to supply privacy or define space. Bearing walls and partitions both supply safe places to run electrical wiring and mount switches, fixtures, and outlets. Walls also supply safe places to run plumbing water supply lines, drains and vents, and heat ducts and registers. An prominent observation is what floor face will fill the void left by discharge of the wall's base moldings and base plate.
People's lifestyles today differ greatly from what was tasteless 30-75 years ago. Larger open areas for attractive and light are much preferred over smaller, hidden spaces, so the underlying reasons for removing walls in older homes are good. But, you've got to first assess what functions a wall serves before deciding whether it's possible to safely remove it entirely or if some kind of structural transfer will be necessary. So, before thoughtless strike with sledge hammers, jack hammers, chain saws, pry bars and backhoes, sniff out some telltale signs of maybe why the wall was built in the first place. Then the fun of dismantling, not demolition, can begin. If you want to make a big mess and cause a lot of dust and needless cleanup work, go ahead, use a sledge hammer and chain saw, but to be most safe and efficient, consequent tips in this guide.
Carpentry Framing
It's prominent to know if a wall is bearing weight to know what the resulting discharge will halt like. Bearing walls carry roof, ceiling, and floor loads. They often run perpendicular to floor and ceiling joists, but there are exceptions. Spotting a bearing wall isn't all the time easy, it may be thrifty or significant to hire an engineer, who also would be able to specify beam sizing and create to replace the bearing wall. That beam may be installed hidden within the done ceiling in line with the floor joists above, or installed hidden in an attic from above with joists hung below with mechanical fasteners. Installed below the joists, the beam can be trimmed as an architectural detail. Cost and practicality will sway create decision.
Before removing the framing of a bearing wall, build a temporary wall to pick up the load. Consider the bearing wall may need reserve on both sides when joists lap. Consider the weight bearing capacity of the underlying floor joists. Additional bracing below may be necessary. Use doubled 2x8 top and base plates to great distribute the load path without knowing ceiling or floor joist layout. The plates could be cushioned with towels to minimize possible damage to the ceiling and floor finishes. Temporarily fasten top plates to ceiling with a join of screws. Cut the temporary brace studs slightly longer to take some weight off the bearing wall and compress towel cushion. Setup them on 16 inch centers with grabber screws to make adjustments and discharge easier. Use of a hydraulic jack may help, but be right not to raise it excessively.
Walls are built in an organized way, and that's the best way to take them down. Wall studs and plates go up first, and they should be taken down last. Trim moldings, casing and base, go in last, and should come off first. Sheetrock or even lath and plaster can be removed in large sections to make cleanup easier. Resolve when to remove floor coverings. maybe rescue vinyl flooring until after lath and plaster discharge will make sweeping up easier and keep debris from falling straight through the subfloor or into the basement. Existing carpeting may cushion and protect underlying hardwood flooring.
Chances are good that electrical wiring is in the wall, even given absence of the inevitable indicators of switches and outlets. Check top plates from the attic and lowest plates from below for wiring penetrations and turn off the affected power circuits. It may be thrifty to hire an experienced licensed and insured electrician to remove or reroute wiring safely.
Plumbing lines may be in the wall. The location of an adjoining, above or below kitchen and bathroom fixtures may indicate approximate plumbing water supply lines or drain and vent lines locations. Turn off the closest water supply valves. It may be thrifty to hire an experienced licensed and insured plumber to remove or reroute plumbing lines safely. Consider heat ducting runs and register locations for future use.
Set up for the wall discharge with appropriate drop cloths. Tape plastic sheets to door openings to sell out opportunity of dust migration. Put an galvanic fan in a window to supply a inevitable airflow out of the room. Wear a dust mask and use eye protection.
Dismantle the wall thought about for safe and sufficient debris removal. Start with casing and base. Run a utility knife straight through the molding edges to break the caulk seams. thought about remove the molding with a pry bar in one piece, especially if the molding is obsolete and must be reused.
A reciprocating saw is the remodeler's best discharge tool. Use of one can become a skill, even a sculptural ar tform. Sheetrock, gyplath, and lath and plaster can be most of course removed by beginning with saw cuts in ceiling and wall corners. Gyplath and lath and plaster usually have expanded metal lath reinforcement in these junctions that can best be cut with a toothless carborundum blade. Large sections of sheetrock can be pried off, especially if screws are removed. Break taped joints with a utility knife. Cut gyplath into sections for removal, as expanded metal lath may again be used as reinforcement at gypboard joints. Lath and plaster is hard to remove in large pieces, you'll just have to be patient. Scraping plaster off the lath may be an sufficient technique to break off the plaster keys. Lath may be thought about pried off studs to sell out personel nail removal.
Before cutting wall studs framing nails with the recipro saw, notch cutouts around wiring and plumbing. A chisel may be helpful to split plates. Remember, only one end of a stud needs to be cut free from nails!
With some planning and care, wall discharge can be done safely and efficiently. If this process seems daunting, if you feel you need only do what you do best to make an income, hire an experienced licensed and insured normal Contractor. Soon, you'll have a more modern, open living space to enjoy. See my website, http://davidtaylorremodeling.com. For more remodeling tips.
A lot of people's first idea in undertaking a remodeling project is to start with tearing down walls. That's an ambitious (if not impulsive) beginning to a project, with focused performance for one's built-up energy, but it's a decision that needs to be well thought about and fully realized before any actual work can safely begin. Walls are built for any reasons, whether as bearing walls designed to hold up a house and transfer loads from above, or as partitions designed to supply privacy or define space. Bearing walls and partitions both supply safe places to run electrical wiring and mount switches, fixtures, and outlets. Walls also supply safe places to run plumbing water supply lines, drains and vents, and heat ducts and registers. An prominent observation is what floor face will fill the void left by discharge of the wall's base moldings and base plate.
People's lifestyles today differ greatly from what was tasteless 30-75 years ago. Larger open areas for attractive and light are much preferred over smaller, hidden spaces, so the underlying reasons for removing walls in older homes are good. But, you've got to first assess what functions a wall serves before deciding whether it's possible to safely remove it entirely or if some kind of structural transfer will be necessary. So, before thoughtless strike with sledge hammers, jack hammers, chain saws, pry bars and backhoes, sniff out some telltale signs of maybe why the wall was built in the first place. Then the fun of dismantling, not demolition, can begin. If you want to make a big mess and cause a lot of dust and needless cleanup work, go ahead, use a sledge hammer and chain saw, but to be most safe and efficient, consequent tips in this guide.
Carpentry Framing
It's prominent to know if a wall is bearing weight to know what the resulting discharge will halt like. Bearing walls carry roof, ceiling, and floor loads. They often run perpendicular to floor and ceiling joists, but there are exceptions. Spotting a bearing wall isn't all the time easy, it may be thrifty or significant to hire an engineer, who also would be able to specify beam sizing and create to replace the bearing wall. That beam may be installed hidden within the done ceiling in line with the floor joists above, or installed hidden in an attic from above with joists hung below with mechanical fasteners. Installed below the joists, the beam can be trimmed as an architectural detail. Cost and practicality will sway create decision.
Before removing the framing of a bearing wall, build a temporary wall to pick up the load. Consider the bearing wall may need reserve on both sides when joists lap. Consider the weight bearing capacity of the underlying floor joists. Additional bracing below may be necessary. Use doubled 2x8 top and base plates to great distribute the load path without knowing ceiling or floor joist layout. The plates could be cushioned with towels to minimize possible damage to the ceiling and floor finishes. Temporarily fasten top plates to ceiling with a join of screws. Cut the temporary brace studs slightly longer to take some weight off the bearing wall and compress towel cushion. Setup them on 16 inch centers with grabber screws to make adjustments and discharge easier. Use of a hydraulic jack may help, but be right not to raise it excessively.
Walls are built in an organized way, and that's the best way to take them down. Wall studs and plates go up first, and they should be taken down last. Trim moldings, casing and base, go in last, and should come off first. Sheetrock or even lath and plaster can be removed in large sections to make cleanup easier. Resolve when to remove floor coverings. maybe rescue vinyl flooring until after lath and plaster discharge will make sweeping up easier and keep debris from falling straight through the subfloor or into the basement. Existing carpeting may cushion and protect underlying hardwood flooring.
Chances are good that electrical wiring is in the wall, even given absence of the inevitable indicators of switches and outlets. Check top plates from the attic and lowest plates from below for wiring penetrations and turn off the affected power circuits. It may be thrifty to hire an experienced licensed and insured electrician to remove or reroute wiring safely.
Plumbing lines may be in the wall. The location of an adjoining, above or below kitchen and bathroom fixtures may indicate approximate plumbing water supply lines or drain and vent lines locations. Turn off the closest water supply valves. It may be thrifty to hire an experienced licensed and insured plumber to remove or reroute plumbing lines safely. Consider heat ducting runs and register locations for future use.
Set up for the wall discharge with appropriate drop cloths. Tape plastic sheets to door openings to sell out opportunity of dust migration. Put an galvanic fan in a window to supply a inevitable airflow out of the room. Wear a dust mask and use eye protection.
Dismantle the wall thought about for safe and sufficient debris removal. Start with casing and base. Run a utility knife straight through the molding edges to break the caulk seams. thought about remove the molding with a pry bar in one piece, especially if the molding is obsolete and must be reused.
A reciprocating saw is the remodeler's best discharge tool. Use of one can become a skill, even a sculptural ar tform. Sheetrock, gyplath, and lath and plaster can be most of course removed by beginning with saw cuts in ceiling and wall corners. Gyplath and lath and plaster usually have expanded metal lath reinforcement in these junctions that can best be cut with a toothless carborundum blade. Large sections of sheetrock can be pried off, especially if screws are removed. Break taped joints with a utility knife. Cut gyplath into sections for removal, as expanded metal lath may again be used as reinforcement at gypboard joints. Lath and plaster is hard to remove in large pieces, you'll just have to be patient. Scraping plaster off the lath may be an sufficient technique to break off the plaster keys. Lath may be thought about pried off studs to sell out personel nail removal.
Before cutting wall studs framing nails with the recipro saw, notch cutouts around wiring and plumbing. A chisel may be helpful to split plates. Remember, only one end of a stud needs to be cut free from nails!
With some planning and care, wall discharge can be done safely and efficiently. If this process seems daunting, if you feel you need only do what you do best to make an income, hire an experienced licensed and insured normal Contractor. Soon, you'll have a more modern, open living space to enjoy. See my website, http://davidtaylorremodeling.com. For more remodeling tips.
No comments:
Post a Comment