Step Up to building Your Own Staircase

It takes patience, diligence and some carpentry skills to institute a good staircase.

Technically, it's not that difficult to build a staircase. The most leading thing about studying how to build stairs is to take precise measurements. Check your calculations so you don't peruse any mistakes After you start building and waste time and money correcting them.

Carpentry Framing

A staircase comprises the stringers, the risers and the treads. The stringers form the framework of the staircase. The risers are the vertical section of each step attached to the front of the stringers. Some staircases have no risers, but they can safe the stringers from weather exposure and prevent accidents. The treads, like the name suggests, are the horizontal part the stairs and are the final pieces in the premise of a staircase.

To build a staircase for your deck, you have to part the total rise, or vertical height from the first done floor to the second done floor. You also have to presuppose the total run needed, which is the horizontal distance in the middle of the landing and the edge of the upper level.

To secure the amount of risers/stairs required, divide the total rise by 7.5. A total rise of 64 inches divided by 7.5 is 9.14. Round this up to the nearest amount and you'll find that you need 9 risers. You need one less tread than a riser because the last step is whether on the ground or same level as the upper floor.

For the height of each riser, divide the total rise by the amount of risers. A total rise of 64 inches spanned by 9 steps requires risers 7.11 inches high. The total run is derived by multiplying the amount of treads (8) by the width of each tread, e.g. 10 inches. Therefore, the total run is 80 inches.

Mark your measurements on 2' x 12' stringers with a framing square. Mark the rise and run (7.11" and 10", respectively) beginning from the top of the stringer. The notches cut out with a circular saw from the first stringer can be used as a pattern for subsequent stringers.

The stringers are attached to the deck by toe-nailing or direct attachment to the framing of the deck itself with joist-hangers. Setup the treads beginning at the bottom. Screws or 3 inch nails are used for this job. Good-quality wood should be used for the treads and done properly to ensure longevity.

Step Up to building Your Own Staircase

It takes patience, diligence and some carpentry skills to institute a good staircase.

Technically, it's not that difficult to build a staircase. The most leading thing about studying how to build stairs is to take precise measurements. Check your calculations so you don't peruse any mistakes After you start building and waste time and money correcting them.

Carpentry Framing

A staircase comprises the stringers, the risers and the treads. The stringers form the framework of the staircase. The risers are the vertical section of each step attached to the front of the stringers. Some staircases have no risers, but they can safe the stringers from weather exposure and prevent accidents. The treads, like the name suggests, are the horizontal part the stairs and are the final pieces in the premise of a staircase.

To build a staircase for your deck, you have to part the total rise, or vertical height from the first done floor to the second done floor. You also have to presuppose the total run needed, which is the horizontal distance in the middle of the landing and the edge of the upper level.

To secure the amount of risers/stairs required, divide the total rise by 7.5. A total rise of 64 inches divided by 7.5 is 9.14. Round this up to the nearest amount and you'll find that you need 9 risers. You need one less tread than a riser because the last step is whether on the ground or same level as the upper floor.

For the height of each riser, divide the total rise by the amount of risers. A total rise of 64 inches spanned by 9 steps requires risers 7.11 inches high. The total run is derived by multiplying the amount of treads (8) by the width of each tread, e.g. 10 inches. Therefore, the total run is 80 inches.

Mark your measurements on 2' x 12' stringers with a framing square. Mark the rise and run (7.11" and 10", respectively) beginning from the top of the stringer. The notches cut out with a circular saw from the first stringer can be used as a pattern for subsequent stringers.

The stringers are attached to the deck by toe-nailing or direct attachment to the framing of the deck itself with joist-hangers. Setup the treads beginning at the bottom. Screws or 3 inch nails are used for this job. Good-quality wood should be used for the treads and done properly to ensure longevity.

Step Up to building Your Own Staircase